Fellows Model 48-12 Large capacity shaper 54" swing, 12" stroke capacity 24" Riser Block Excellent!

 DESCRIPTION / QUOTATION
We offer, subject to prior sale:

One (1) - Model No. 48-12 FELLOWS Vertical Gear Shaping Machine, suitable
for the manufacture of internal and external spur gears, (as well as helical
gears with proper guides), up to 48” (1219mm) pitch diameter, 12” (305mm)
face-width, and 2 DP (module 12.7).

Serial No. 35081 (New 1974)

The machine corresponds to the attached copy of factory literature,
featuring the following:

EQUIPMENT / FEATURES:
• straight spur guide for cutter-spindle
• pneumatic assist for moving of work apron plus apron support
• special 24” (609.6) height riser-block providing roughly 25.81” (655.6mm)
total work-piece & fixture clearance height
• dial set gear box providing 12 stroking speeds (from 12 to 190 S.P.M.)
• twelve (12) different rotary feeds (from .0006 to .007 per inch of cutter
P.D.)
• 5” diameter heavy-duty, hollow cutter-spindle 
• two (2) standard cutter adaptors
• dial with adjustable trip dogs for depth feed control and number of cuts
• work-spindle fast rotation for truing work
• rapid traverse for cutter-saddle
• operator’s pendant control
• 48” diameter T-slotted work sub-table
• power forced lubrication system to all elements 
• self-contained coolant system for cutting oil
• assortment of change gears (approx.35-gears)
• full complement of electrics (motors/controls)(presently arranged for
3-phase 220/440 Volt, 60 Hz operation)
• operator’s manual, parts list, wiring diagrams

PRINCIPAL SPECIFICATIONS:
Maximum pitch diameter...........................................48"(1219mm)
Maximum diameter work-piece or fixture...........................54”(1372mm)
Max. center distance between work-table and cutter-spindle
centerline (external gear)....................................28.5”(723.9mm)
Max. center distance between work-table and cutter-spindle
centerline (internal gear)..................................21.25”(539.75mm)
Maximum pitch spur........................................2 DP (module 12.7)
Maximum pitch helical......................................3 DP (module 8.5)
Maximum nominal face width internal/external......................12”(305mm)
Maximum stroke length............................................13”(2870mm)
Maximum helix angle (w/proper guides)............................45 degrees
Max. distance work table surface to underside of cutter spindle
in upper-most position.......................................25.81”(655.6mm)
Cutter spindle taper bore......................................No. 18 Jarno
Work spindle bore diameter.................................5.875”(149.225mm)
Saddle back-off after completion of cut......................1.140”(28.96mm)
Maximum weight face plate, fixture and part..............2,750 Lbs(1250 kGs)
Cutter Spindle diameter............................................5”(127mm)
Stroking speeds (12)..........................................12 to 190 SPM
Machine dimensions...................92” x 76” x 141” (2337 x 1930 x 3581mm)
Machine net weight, approx...........................22,000 lbs.(10,000 kGs)

* * * * *
For the machine professionally “reconditioned”
o machine thoroughly cleaned
o all worn and/or broken parts repaired or replaced
o lubrication and electrical system reviewed
o machine checked for proper function
o machine prepped and painted per customer's specified paint scheme

EXTRA for EXPORT:
For base machine dismantling and placing on two (2) 
heavy duty wooden platform skids, vacuum-wrapped,
including boxing of accessories, transport/freight to export 
packer’s facility, including export packing/preserving for 
sea-worthy transport into 40-Ft. “High Cube” ocean 
cargo container, with delivery C.I.F WILL ADVISE … ( upon request )

* * * * *
NOTE: The aforementioned description and list of accessory equipment is
correct and accurate to the best of our knowledge. However, it is not
binding in any regard, as we reserve the right to change and/or alter same
without prior notice. Consequently, the buyer is responsible for confirming
same upon physical inspection and inventory of the machine and all related
accessory equipment.

Contact Rich Piselli to set up an under power inspection.